Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Installation for Tomball Homeowners
A new driveway gate in Tomball typically costs between $4,200 and $11,500 installed, depending on the gate material, the automation system, and how much site preparation the column bases need. We install gates that open every time: driveway gates, pedestrian gates, sliding gates, swing gates, double gates, and security gates, all with a written price handed to you before any work starts. Adrian Vance founded Vance Gate Repair in 2014 after years of commercial access-control documentation work, and that habit carries into every residential gate we install in Tomball, Pinehurst, and The Woodlands. You get a written scope, a written price, and a photo record of what we installed before we leave your driveway.
Tomball’s clay soil shifts with rain and drought, and that movement is why column footings here need more depth than builders in other parts of Harris County sometimes assume. We dig footings to a depth that accounts for that movement, then photograph the footing before concrete goes in. That photo stays in your job file. If a gate column ever drifts out of plumb years later, we know exactly how it was built and where to look first. Call (346) 248-7685 for a free in-person estimate in Tomball. A live person answers at any hour.
Related: learn more about Gate Installation in Tomball or start with our home page for an overview of every service we provide.
What Our Gate Installation Service Includes
Driveway Gate Installation
A driveway gate is the single largest security and curb-appeal decision most Tomball homeowners make on their property. We install single and double driveway gates, manually operated or fully automated, with the right hardware for the gate’s weight and the number of cycles it will see each day. In communities like Pinehurst and Jersey Village, where a driveway gate is often the first thing a visitor notices, we take extra care to set the reveal, the latch alignment, and the opener arm geometry so the gate never drags. Every driveway gate installation includes a documented photo record of the footings, the hinges, the opener mounting, and the final travel adjustment.
Pedestrian Gate Installation
A pedestrian gate gives you a separate entry point without opening the full driveway every time someone walks up. We build and install pedestrian gates alongside existing fencing or as part of a new gate package, using steel or aluminum frames sized to the opening and matched to the look of your driveway gate. Tomball’s afternoon thunderstorms mean pedestrian gate hardware needs to be rated for wet conditions, and we use sealed bearing hinges and stainless fasteners on every install. If you want a pedestrian gate keyed or equipped with its own access control, we can run that at the same time.
Sliding Gate Installation
Sliding gates are the right choice on Tomball properties where a swing gate would block the driveway or a sloped apron makes swing geometry impractical. We build sliding gates on a cantilever design when possible, which means the gate does not drag a roller through dirt and mud, or we install V-track systems where cantilever mounting isn’t an option. The gate’s weight, the post spacing, and the opener torque have to be calculated together, and we photograph every measurement and every setting before and after the final test run. In areas like Spring and Conroe where lots can run deeper than they do in the inner suburbs, a well-built sliding gate opens the same at year five as it does at week one.
Swing Gate Installation
Swing gates remain the most common gate type in Tomball, and most failures we see on newer installations trace back to undersized hinges or a column poured too shallow. We build swing gates with commercial-grade hinge hardware that carries the gate’s full weight without sagging, and we set opener arms at the correct distance from the hinge so the motor never fights the gate. Every swing gate install includes a limit-switch reading on the opener and a photo of that reading. The Haven Standard, our written operating standard since 2014, requires that level of documentation on every visit, not just when something goes wrong.
Double Gate Installation
A double gate spans a wider driveway opening with two leaves that meet in the middle, and the success of that design lives in the center latch and the synchronized openers. We install double gates with matched opener systems that communicate properly, so one leaf never arrives ahead of the other and the center stop never takes a hit. In Tomball, where many custom homes have wider drives than the metro core, a double gate often fits the opening better than one long single leaf. We set the overlap, the catch post, and the safety photo-eyes, then run the gate through 20 full open-close cycles before we call the job done and hand you the photo log.
Security Gate Installation
A security gate is built for the person who wants more than curb appeal: a taller frame, a locking mechanism that resists prying, and often integrated access control. We install security gates in Tomball with code panels, keypads, and in some cases a cellular intercom that lets you see and talk to whoever is at the gate from your phone. The power run and the safety edges are planned before the first post hole is dug, and we document the wire path and the connection points exactly as they are built. If you already have a security gate and need it serviced, we work on whatever is already on the property rather than steering you toward a replacement.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Installation
We install and service Viking gate openers more than any other brand on residential properties in the Tomball area. Viking swing and slide operators run on proven AC or DC platforms, and we know their control board revisions well enough to wire them correctly the first time and set the force limits without guesswork. When we install a Viking opener, we photograph the control board before power is applied and again after the final adjustment.
Ghost Controls and DoorKing also come through our Tomball truck regularly, and we treat every brand the same way: the opener gets matched to the gate’s weight and cycle count, not the other way around. Ghost Controls’ battery-backed kits work well on rural properties around Pinehurst and Prairie View where power blips are common, and DoorKing’s slide and swing operators are a fit for heavier gates on acreage lots around Katy and Willis. If you already have an Elite operator on the property, we service that too and stock common replacement parts for it. You don’t need to know which brand you have before we arrive. We identify it, price the job in writing, and install to the manufacturer’s spec as well as our own.
BeforeAfterSigns You Need Gate Installation Right Now
- The gate hangs visibly out of level when it’s halfway open. A gate that dips toward the latch end has either a hinge that is pulling out of the column or a column that was never set deep enough for Tomball’s clay. The longer it runs out of level, the more it loads the opener motor and the more it grinds the latch hardware.
- The opener brand on the property is no longer supported or parts have become hard to find. When a homeowner can’t get a control board or a limit switch for the motor already installed, replacing the opener is cheaper than waiting for the failure. We price the opener replacement as a line item with a written quote, never a verbal estimate.
- The gate was hit by a vehicle or backed into by a delivery truck. Even a slow hit can bend the gate frame, crack a column, or knock the opener arm out of geometry. A gate that still opens after an impact is working harder than it should, and the strain lands on the motor and the hinges.
- The existing gate does not meet the property’s current security needs. A three-foot ornamental gate around a backyard pool is not the same thing as a security gate, and Tomball homeowners who add a pool, a workshop, or a home office often need a different gate altogether. We can install a security gate that integrates an intercom or keypad without tearing out the existing fence.
- The gate was installed by a handyman or a fence company that did not run the automation. The concrete work and the fence line may look fine, but if there is no power run, no photo-eye, and no opener, the gate is a manual leaf. Upgrading it now costs less than redoing the driveway later, and we can handle the power run, the safety edges, and the opener as one package.
Our Gate Installation Process - Step by Step
- 1
Site visit and load calculation. We measure the opening, check the slope at the drive apron, test the soil at the post locations, and weigh the gate or calculate its weight from the material spec. If there is an existing opener, we note its model and condition. From this we produce a written scope and a flat price, which we hand to you before you make any commitment. That is Haven Standard Clause 1: have it in writing.
- 2
Material order and fabrication. Once you approve the written price, we order the gate frame and panels, the opener, and any access control components. For custom gates, fabrication runs on a measured schedule, not a promise of same-day installation. We tell you the lead time up front and keep it.
- 3
Footing excavation and column set. We dig below the local frost and moisture line and set the steel reinforcement before concrete goes in. Photos are taken at this stage: the excavation, the rebar cage, and the concrete pour. These photos are part of the job file, and they are what allow us to guarantee our column work against settling.
- 4
Hang, square, and automate. The gate is hung on its hinges or set on its track, then leveled and latched. The opener is mounted, wired, and programmed. Photo-eyes are aligned, the force or torque limit is set, and the gate is run through repeated open-close cycles. If you have a keypad or intercom, we program and test it at this stage as well.
- 5
Walkthrough, documentation, and closeout. Before we leave, we walk the gate with you: open and close it together, trigger the safety reverse, and show you the disconnect. Then we hand over the photo record and the written record of what was installed. Every installation, like every repair, gets the same closeout under Clause 4: evidence on every job.
How Much Does Gate Installation Cost in Tomball?
A manual driveway gate for a standard Tomball residential opening typically runs between $4,200 and $7,800, while a fully automated swing or sliding gate with a quality opener like DoorKing or Viking usually lands between $6,500 and $11,500. For more detail, see our guide to Gate Installation pricing. A pedestrian gate installed next to existing fence typically runs between $1,800 and $3,400. Double gates and security gates sit at the higher end of the range because the frame, the reinforcement, and the opener pair all cost more. Your exact price depends on the gate material and size, the opener brand, the amount of concrete work the columns require, and whether we are running new power from the house to the gate.
What affects the price most often in Tomball is not the gate itself; it’s the footing depth and the power run. A driveway gate 60 feet from the house needs conduit and wire run the whole distance, and a gas or water line in the path changes that estimate on the spot. We quote the full scope in writing before we start, including the power run and any concrete, so there is no extra invoice at the end. You will also get a free second opinion on any written estimate from another company: bring us the paperwork and we will review it at no cost.
A free in-person estimate includes the gate measurement, the soil check, and the written price. Call (346) 248-7685 and we will set a time, not a callback.
Gate Installation Near Tomball - Our Service Area
We install gates throughout Tomball and the surrounding communities, including Pinehurst, The Woodlands, Spring, Jersey Village, Conroe, Aldine, Prairie View, Humble, Hunters Creek Village, Willis, and Katy. For installation work, we schedule a measured appointment rather than a same-day dispatch; fabrication and concrete work cannot be rushed safely, and we will not promise a faster date than the materials allow. What we do promise is a written price and a date we keep. If you are in Pinehurst, we often recommend a cantilever slide design because of the sandy soil patches there, and for The Woodlands, driveway slope and HOA review are usually the two biggest factors. Wherever you are in the Tomball area, the same written-price and photo-record standard applies.
Serving Tomball, TX - Our Local Coverage Area
We’re based in the Tomball area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Installation in Tomball
Gate installation is the full process of building a gate at an opening in a fence or driveway: measuring the opening, setting the columns or posts, hanging the gate, and installing the opener and safety equipment if the gate is automated. In Tomball, we also handle the power run from the house to the gate, which is part of what separates a driveway gate that opens every day from one that becomes a manual gate after six months. Every installation we do ends with a walkthrough and a photo record of the work.
A standard driveway gate installation in Tomball usually takes two to three days on site, with the concrete work done on day one and the gate and opener completed after the concrete cures. Custom gates that must be fabricated to size add lead time, typically one to three weeks depending on the material and the fabricator’s schedule. We give you the timeline in writing with the price, and we do not start tearing anything out until you have approved both.
A typical residential driveway gate in Tomball runs $4,200 to $11,500 installed, with manual gates at the lower end and automated double or security gates at the higher end. The major cost drivers here are the gate weight and material, the opener brand, the footing depth, and how far the power has to be run from the house. We hand you a flat written price before any work begins, so the number you approve is the number you pay. Call (346) 248-7685 for an exact quote; estimates are free.
Yes, we install and service Viking, Ghost Controls, DoorKing, and Elite openers, along with five other major brands. We wire each one to the manufacturer’s specification and then set the force limits and travel stops by testing the actual gate, not by copying a factory default. If your existing opener is a brand we service, we repair it rather than steering you toward a replacement unless the cost of the repair exceeds the value of the unit.
If your gate has failed and is stuck open or stuck closed, we treat that as a repair emergency and can often get a technician to Tomball the same day. For a full new installation, we cannot safely pour concrete and mount an opener in one evening, and we will not pretend otherwise. We will schedule the soonest real date we can, and the date we give you is the date we show up.
Every completed installation is covered by our 365-Day Done Right Promise: if anything about the install is not right within one full year, we make it right at no additional charge. That includes the gate, the opener, the wiring, and the concrete work. The same promise applies to every repair and every service we perform, and it is backed by the photo record and written documentation we leave with you.
Clear the area around the gate opening: move vehicles, trash bins, and anything else at least 10 feet back from the work zone on both sides of the fence. If you have irrigation lines near the post locations, mark them with flags or tell us during the site visit so we can adjust the dig. If your HOA requires approval for gate work, start that process early; in communities around The Woodlands and Jersey Village, that approval can add time to the schedule. We handle the rest and provide the written scope and price before anything is torn out.
Schedule Your Gate Installation Service in Tomball Today
If you are ready to get a written number for your gate, call (346) 248-7685 for a free in-person estimate at your Tomball property. We will measure the opening, check the soil, and hand you a flat price before you commit to anything. You will know the full cost before the first post hole is dug, and you will have the photo record to prove what was installed. A live person answers the phone at any hour, every day.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Tomball since 2014.