Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Aldine, TX
Gate access control and parts work in Aldine skews toward what the I-45 and Beltway 8 corridors demand: heavy-duty hardware that survives constant use, clay soil that moves, and humidity that does not forgive cheap steel. Most calls we run in Aldine involve either a commercial slide gate at a trucking yard or freight warehouse that has to pass 18-wheelers every few minutes, or an older residential security gate on a poured concrete post that Harris County’s expansive clay has finally pushed out of plumb. Call (346) 248-7685 and you’ll get a live person who can tell you what a technician will actually do before we send one.
Why Aldine Homes Are Different
Aldine’s residential neighborhoods were largely built from the 1960s through the 1980s, and the original gates on those tracts are now forty to sixty years old. Most sit on poured concrete posts that were set at a depth that made sense before anyone really understood Beaumont clay. The soil here expands after heavy rain and contracts during summer dry spells, and that cycle tilts posts a little more each year until the gate starts dragging across the driveway or the latch no longer lines up. It is a near-universal complaint in Aldine’s older side-yard gate setups.
The other Aldine-specific factor is industrial. The freight corridors along I-45 and Beltway 8 North, tied to Bush Intercontinental Airport’s cargo traffic, mean gate repair here is not the same job as it is in Spring or The Woodlands. We work on cantilever slides and v-track slides built for high-cycle commercial passage, not just residential swing gates. And the humidity off Greens Bayou accelerates rust on ornamental iron and corrodes operator circuit boards faster than nearly any other metro in Texas. A gate that would last twenty years in Midland lasts eight here if the installation was not weatherproofed correctly.
Our Main Aldine Services
These three services represent the bulk of what we do in Aldine, from high-cycle commercial repair to full residential installations and operator work on existing gates.
Gate Repair in Aldine
Repair in Aldine usually comes down to either mechanical failure from soil movement, or operator failure from moisture and duty cycle. We see broken hinges, sagging weld joints, wheels that have ground flat, and photo-eyes knocked out of alignment by shifting posts. On the commercial side, a slide gate that binds against its rail can take an operator out within a week if nobody catches it. We diagnose, quote a written price, and fix. Gate Repair in Aldine.
Gate Installation in Aldine
New installations in Aldine require planning for what the soil will do, not just what the gate weighs today. We set posts deeper than the original builders did when possible, use heavier gauge steel where clay movement is likely, and select track systems that tolerate slight grade shifts. Whether it’s a side-yard gate for a long narrow Aldine lot or a commercial slide at a freight access point, the scope and price are written before any work begins. Gate Installation in Aldine.
Gate Motor & Opener in Aldine
Motor work in Aldine often involves an operator that has been cycling dozens or hundreds of times daily for years in high humidity. Circuit boards corrode, transformers short, and gear trains wear out. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, with parts runs available same day for most common failures. Gate Motor & Opener in Aldine.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Aldine
Gate access control in Aldine is a different discipline than in the purely residential suburbs around it. The trucking yards and freight warehouses near I-45 and Beltway 8 North run gates that cycle heavily all day, and the access systems on those gates have to hold up to humidity that kills circuit boards early. Add in the older residential stock, where homeowners want keypad or remote entry on a gate that has shifted out of plumb because of clay soil, and you end up needing a company that understands both sides. Gate Access Control covers commercial keypad and telephone entry systems, residential remotes, and video intercom setups on gates of any age.
Keypad Entry
Signs you need it
The keypad works intermittently after rain, or certain buttons need to be pressed twice before they register.
What it costs in Aldine
Keypad replacement or installation typically runs $189 to $325 depending on whether we are wiring a standalone unit or integrating with an existing operator.
How we do it
We mount the keypad at the correct height, run weather-sealed wiring, program the codes in front of you, and leave a photo record of the wiring connections.
Remote Control
Signs you need it
The gate only opens from one remote, or a remote that used to work from forty feet now only works from ten.
What it costs in Aldine
Transmitter replacement and programming usually runs $85 to $185, and a new receiver board runs $250 to $400.
How we do it
We test signal strength at the gate, replace the transmitter or receiver, program all existing remotes back in, and document the dip switch or rolling code settings.
What Gate Access Control Costs in Aldine
| Item | Typical range in Aldine |
|---|---|
| Keypad replacement | $189 - $325 |
| Remote transmitter | $85 - $185 |
| Receiver board | $250 - $400 |
Can you integrate access control with an existing gate operator?
Yes, in most cases we can. We match the new keypad, card reader, or intercom to the operator’s control board, regardless of whether the motor is LiftMaster, Linear, BFT, Viking, or another brand. Call (346) 248-7685 and we will tell you what is compatible.
What happens to my access codes during a repair?
We keep your existing codes where possible and only reprogram when the board has been replaced. Any new codes are tested in front of you before we leave.
Gate Parts & Welding in Aldine
Gate parts and welding in Aldine often means repairing hardware that was not made for the soil it sits in or the humidity it breathes. On the residential side, we see hinges that have rusted through on ornamental iron gates, posts that have tilted so far the gate will not latch, and side-yard gates that drag because the original pour was too shallow for Beaumont clay. On the commercial side, it is heavy wear: gate rollers flattened from constant use, slide rails bowed by truck traffic, and welds that fatigue after thousands of cycles. Gate Parts & Welding covers replacement and repair on all of it, with welding done on-site where the gate stands.
Hinge Replacement
Signs you need it
The gate sags at the latch end and scraping marks appear on the concrete where it drags.
What it costs in Aldine
Hinge replacement typically runs $180 to $400 per hinge, including labor and the cost of the hinge itself.
How we do it
We support the gate, cut or unbolt the failed hinge, weld or bolt the replacement, and re-plumb the gate before testing the swing.
Post Replacement
Signs you need it
The post visibly leans, or the gate whips in the wind because the post has lost its hold in the clay.
What it costs in Aldine
Post replacement runs $400 to $800 for a standard residential gate post, set deeper and with proper root protection against the clay movement.
How we do it
We dig out the old footing, set a new post at the correct depth with additional concrete mass, and align the gate before we leave a photo record.
What Gate Parts & Welding Costs in Aldine
| Item | Typical range in Aldine |
|---|---|
| Hinge replacement | $180 - $400 per hinge |
| Post replacement | $400 - $800 per post |
| Gate roller replacement | $120 - $350 per roller |
Can you weld cast iron gates, or only steel?
We weld steel and most ornamental iron. True cast iron requires specialized rod and preheating, and in those cases we will tell you honestly whether the part should be replaced instead.
Do I have to remove the gate to get it welded?
No. Most hinge and crack repairs are done with the gate in place. Removing a gate adds labor and risk to the posts, so we avoid it unless the frame is too far gone.
Brands We Service in Aldine
We service operators and access hardware from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Parts for the most common failures in Aldine are stocked locally, which means less waiting on shipping when a circuit board or gear train dies. See our brands for detail.
Pricing for Gate Repair in Aldine, TX
| Service | Typical range in Aldine |
|---|---|
| Hinge replacement | $180 - $400 per hinge |
| Post replacement | $400 - $800 per post |
| Keypad replacement | $189 - $325 |
| Remote transmitter | $85 - $185 |
| Receiver board | $250 - $400 |
| Gate roller replacement | $120 - $350 per roller |
| Rail repair | $250 - $600 |
| Custom welding (per joint) | $90 - $250 |
In Aldine, two things push a price higher than the baseline: a gate that has shifted so badly it needs post work before any hinge or roller makes sense, and commercial gates that need to stay in service while we repair them. The figure we write down before starting includes the work and the parts. It does not grow while the job is in progress.
Neighborhoods We Serve in Aldine
We work across Aldine, from the residential blocks off Aldine Mail Route to the commercial corridors along I-45 and Beltway 8 North. Response times vary with the day, but most Aldine calls can be scheduled within one to two business days, with emergency repair available sooner.
- Greenspoint area
- Aldine Gardens
- Hidden Valley
- East Aldine
- Airline Road corridor
Service Area - Cities Near Aldine
We also handle gate repair and access work in Tomball, TX, Pinehurst, TX, The Woodlands, TX, and Spring, TX. Dispatch and scheduling are coordinated from the brand’s Houston office, and crews serve Aldine locally.
Serving Aldine, TX - Our Local Coverage Area
We’re based in the Aldine area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Aldine
Most non-emergency repairs are scheduled within one to two business days. If a commercial gate is stuck open or a residential gate will not close, we treat it as an emergency and dispatch the next available technician. Call (346) 248-7685 and ask for the fastest slot.
Most repairs and part replacements require no permit. A new installation with a concrete pour or electrical run may need one depending on the scope, and we will tell you before the job starts if that applies to your property.
Yes. Cantilever and v-track slide gates make up a significant share of our Aldine work, and our technicians are equipped for heavy-duty hardware and operators that run high cycle counts. We service them the same way we do residential gates: written price first, documented record when we leave.
Call (346) 248-7685 for a free estimate on any gate repair, access control, parts, or welding work in Aldine. A live person picks up, and you’ll get a written price before any tool is picked up.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Aldine Customers Say
"Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.